交通工具空氣吊掛氣囊故障解決方法？

Solutions to the problems of vehicle air suspension airbag:

空氣彈簧在交通工具領域的運用已經是見慣不怪了，那么，當空氣吊掛氣囊顯露出來故障時你又會不會解決呢？今天我們就來學習一下子交通工具空氣吊掛氣囊顯露出來故障的解決方法。

Air springs have become commonplace in vehicles, but will you be able to fix the problem when air bags show up?Today we're going to learn how to fix a problem that has suddenly become apparent in the air bag on a vehicle.

空氣吊掛氣囊最常見的故障就是氣囊無氣和氣囊皺褶，造成這兩種故障顯露出來的原因有可能不盡相同，處置的方法也不同，實際碰到時我們要仔細分析原因并覺得合適而運用準確的方法處置。

The most common faults of air suspension airbag are airbag airbag without air and airbag fold. The causes of these two kinds of faults may be different, and the disposal methods are also different. When actually encountered, we should carefully analyze the causes and find appropriate and accurate methods for disposal.

1.氣囊無氣：這種物質情形檢查起來比較簡單，我們先來熟悉一下子空氣吊掛的氣路結構，空氣吊掛彈簧的氣源由制動系統接出來，通過壓力盡量照顧閥，存放在專用的儲鼓動工具內。所以顯露出來這種原因的物質情形有可能是空氣吊掛專用儲鼓動工具無氣或壓力很低；空氣管兒路阻塞或打折；水平高度閥聯接桿脫落。我們?cè)跈z查時可以逐個排查，找出原理處置問題就不難了。

1. Airbag is airless: this material is relatively simple to check. Let's get familiar with the air circuit structure of air suspension.Therefore, it is possible that the material condition of such a cause is that the air hanging special storage and agitation tool has no air or the pressure is very low;Air duct blocked or discounted;Horizontal height valve connecting rod falls off.We can check them one by one during the inspection. It is not difficult to find out the principle and solve the problem.

2.氣囊皺褶：顯露出來這種故障有可能是車輛轉運吊裝時，氣囊被拉伸出來較多，未復位正常，造成氣囊皺褶。具體的解決方法是拆白開水平高度閥的豎桿子下方橡膠聯接件與車橋的聯接，將桿子進步提，等整個氣囊充足氣后，之后將桿子裝回去，氣囊即可還原正常理形?？諝鈴椈傻念A(yù)設并不是想象中那末簡單的，他在交通工具上的作用也是很重要的，所以顯露出來故障要及時處置，假設真的是沒有方法處照理應該該送去檢查修理保證行車安全。

   2. Airbag fold: this fault may be caused by the fact that when the vehicle is transferred and hoisted, the airbag is stretched out frequently and is not reset normally, resulting in airbag fold.The concrete solution is to remove the connection between the rubber joint under the vertical pole of the plain water valve and the axle, and improve the pole. After the entire air bag is fully inflated, the pole can be put back and the air bag can be restored to its normal shape.The preset of the air spring is not as simple as imagined, and its role on the vehicle is also very important. Therefore, if the fault is revealed, it should be dealt with timely. If there is no way to deal with it, it should be sent to check and repair to ensure the safety of driving.